Show simple item record

dc.contributor.advisorPinnau, Ingo
dc.contributor.authorAl Sunbul, Yasmeen
dc.date.accessioned2018-05-16T07:56:40Z
dc.date.available2018-05-16T07:56:40Z
dc.date.issued2018-04
dc.identifier.citationAl Sunbul, Y. (2018). Boron Removal from Seawater by Thin-Film Composite Reverse Osmosis Membranes. KAUST Research Repository. https://doi.org/10.25781/KAUST-P50TT
dc.identifier.doi10.25781/KAUST-P50TT
dc.identifier.urihttp://hdl.handle.net/10754/627887
dc.description.abstractReverse Osmosis membranes have been successfully proven to remove almost 99% of chemicals dissolved in seawater. However, removal of certain trace elements, such as boron is challenging and relatively low for seawater reverse osmosis desalination plants compared to thermal desalination plants. Boron is naturally occurring and is present in seawater at an average concentration of 4.5-5 mg/L. While boron is a vital element, its toxicity has been proven on crops, animals and possibly humans. Additionally, boron should be removed to comply with the current guideline value of 0.5 mg/L, for drinking water, issued by the World Health Organization (WHO), which is barely attained by a single-pass process seawater reverse osmosis plant. Currently, multipass reverse osmosis membrane operations with pH modifications are the only valid method for boron removal. However, this is not economically efficient as it requires higher energy and chemicals consumptions. The objective of this study was to investigate boron removal by commercial TFC RO membranes in addition to custom-made KAUST-synthesized TFC membrane. Five membrane samples were examined: Toray, Sepro, Koch, and KAUST in-house synthesized membrane. Three different feed pH conditions were used: pH6, pH8, and pH10. Filtration experiments were conducted in two parts. In experiment 1, all five membranes were examined for boron rejection in a dead-end permeation system, whereas in experiment 2 the two membranes with the highest boron rejection from experiment 1 were tested in a cross-flow system. Permeate and feed samples were taken continuously and analyzed for boron concentration, rejection calculation. Membrane surfaces were characterized according to hydrophilicity, roughness and surface charge. The results showed for all the tested membranes that boron rejection increased as the feed pH increased. KAUST, defect-free TFC, showed the highest performance for boron rejection for all pH conditions, although, it shows the roughest surface. Toray membranes 80LB and 80B exhibited the second highest boron rejection and had the most negatively charged membrane surfaces. It was observed in this study that the rejection of boron by a membrane is due to size exclusion and charge repulsion mechanisms. It was concluded that, the KAUST, defect free TFC has the potential to be applicable for boron rejection in industrial application as it has better boron rejection than commercially available RO membranes.
dc.language.isoen
dc.subjectBoron
dc.subjectReverse Osmosis
dc.subjectRemoval
dc.subjectTFC
dc.subjectMembranes
dc.titleBoron Removal from Seawater by Thin-Film Composite Reverse Osmosis Membranes
dc.typeThesis
dc.contributor.departmentPhysical Science and Engineering (PSE) Division
thesis.degree.grantorKing Abdullah University of Science and Technology
dc.contributor.committeememberPeinemann, Klaus-Viktor
dc.contributor.committeememberHan, Yu
thesis.degree.disciplineChemical and Biological Engineering
thesis.degree.nameMaster of Science
refterms.dateFOA2018-06-13T20:14:10Z


Files in this item

Thumbnail
Name:
Yasmeen_Al_Sunbul_Thesis.docx Final.pdf
Size:
3.087Mb
Format:
PDF
Description:
Yasmeen Al Sunbul - Final Thesis Paper

This item appears in the following Collection(s)

Show simple item record