Show simple item record

dc.contributor.authorShan, Meixia
dc.contributor.authorSeoane, Beatriz
dc.contributor.authorAndres-Garcia, Eduardo
dc.contributor.authorKapteijn, Freek
dc.contributor.authorGascon, Jorge
dc.date.accessioned2017-12-14T12:34:04Z
dc.date.available2017-12-14T12:34:04Z
dc.date.issued2017-12-07
dc.identifier.citationShan M, Seoane B, Andres-Garcia E, Kapteijn F, Gascon J (2017) Mixed-Matrix Membranes containing an Azine-Linked Covalent Organic Framework: Influence of the polymeric matrix on Post-Combustion CO 2 -capture. Journal of Membrane Science. Available: http://dx.doi.org/10.1016/j.memsci.2017.12.008.
dc.identifier.issn0376-7388
dc.identifier.doi10.1016/j.memsci.2017.12.008
dc.identifier.urihttp://hdl.handle.net/10754/626376
dc.description.abstractThe use of an azine-linked covalent organic framework (ACOF-1) as filler in mixed-matrix membranes (MMMs) has been studied for the separation of CO2 from N2. To better understand the mechanisms that govern separation in complex composites, MMMs were prepared with different loadings of ACOF-1 and three different polymers as continuous phase: low flux-mid selectivity Matrimid®, mid flux-high selectivity Polyactive™ and high flux-low selectivity 6FDA:DAM. The homogeneous distribution of ACOF-1 together with the good adhesion between the ACOF-1 particles and the polymer matrices were confirmed by scanning electron microscopy. In mixed-gas CO2/N2 separation a clear influence of the polymer used was observed on the performance of the composite membranes. While for Matrimid® and 6FDA:DAM an overall enhancement of the polymer's separation properties could be achieved, in case of Polyactive™ penetration of the more flexible polymer into the COF porosity resulted in a decreased membrane permeability. The best improvement was obtained for Matrimid®-based MMMs, for which a selectivity increase from 29 to 35, together with an enhancement in permeability from 9.5 to 17.7 Barrer for 16wt% COF loading, was observed. Our results demonstrate that the combination of the filler-polymeric matrix pair chosen is crucial. For a given filler the polymer performance improvement strongly depends on the polymeric matrix selected, where a good match between the discontinuous and continuous phase, both in the terms of compatibility and gas separation properties, is necessary to optimize membrane performance.
dc.description.sponsorshipB.S. gratefully acknowledges the Netherlands National Science Foundation (NWO) for her personal VENI grant. J.G. acknowledges financial support of the European Research Council under the European Union's Seventh Framework Programme, ERC Grant Agreement no. 335746, CrystEng-MOF-MMM. Meixia Shan gratefully acknowledges the support from the China Scholarship Council.
dc.publisherElsevier BV
dc.relation.urlhttp://www.sciencedirect.com/science/article/pii/S0376738817323682
dc.rightsNOTICE: this is the author’s version of a work that was accepted for publication in Journal of Membrane Science. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Membrane Science, 6 December 2017. DOI: 10.1016/j.memsci.2017.12.008. © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/
dc.subjectCovalent organic frameworks
dc.subjectmixed-matrix membranes
dc.subjectCO2/N2 separation
dc.subjectCO2 capture
dc.titleMixed-Matrix Membranes containing an Azine-Linked Covalent Organic Framework: Influence of the polymeric matrix on Post-Combustion CO 2 -capture
dc.typeArticle
dc.contributor.departmentChemical Engineering Program
dc.contributor.departmentKAUST Catalysis Center (KCC)
dc.contributor.departmentPhysical Science and Engineering (PSE) Division
dc.identifier.journalJournal of Membrane Science
dc.eprint.versionPost-print
dc.contributor.institutionCatalysis Engineering, Chemical Engineering Department, Delft University of Technology, van der Maasweg, 9, 2629 HZ Delft, The Netherlands
dc.contributor.institutionFaculty of Science, Debye Institute for Nanomaterials Science, Utrecht University, Universiteitsweg 99, Utrecht 3584 CG, The Netherlands
kaust.personGascon, Jorge
dc.date.published-online2017-12-07
dc.date.published-print2018-03


Files in this item

Thumbnail
Name:
1-s2.0-S0376738817323682-main.pdf
Size:
2.036Mb
Format:
PDF
Description:
Accepted Manuscript
Thumbnail
Name:
mmc1.docx
Size:
2.765Mb
Format:
Microsoft Word 2007
Description:
Supplemental files
Thumbnail
Name:
1-s2.0-S0376738817323682-fx1.jpg
Size:
51.25Kb
Format:
JPEG image
Description:
Graphical abstract

This item appears in the following Collection(s)

Show simple item record