• Analysis of the current–voltage curves and saturation currents in burner-stabilised premixed flames with detailed ion chemistry and transport models

      Belhi, Memdouh; Han, Jie; Casey, Tiernan A.; Chen, Jyh-Yuan; Im, Hong G.; Sarathy, S. Mani; Bisetti, Fabrizio (Combustion Theory and Modelling, Informa UK Limited, 2018-05-22) [Article]
      Current-voltage, or i–V, curves are used in combustion to characterise the ionic structure of flames. The objective of this paper is to develop a detailed modelling framework for the quantitative prediction of the i–V curves in methane/air flames. Ion and electron transport coefficients were described using methods appropriate for charged species interactions. An ionic reaction mechanism involving cations, anions and free electrons was used, together with up-to-date rate coefficients and thermodynamic data. Because of the important role of neutral species in the ion production process, its prediction by the detailed AramcoMech 1.4 mechanism was optimised by using available experimental measurements. Model predictions were evaluated by comparing to i–V curves measured in atmospheric-pressure, premixed, burner-stabilised flames. A detailed evaluation of the reliability of ion kinetic and transport parameters adopted was performed. The model provides good quantitative agreement with experimental data for various conditions.
    • Estimating and understanding the efficiency of nanoparticles in enhancing the conductivity of carbon nanotube/polymer composites

      Mora Cordova, Angel; Han, Fei; Lubineau, Gilles (Results in Physics, Elsevier BV, 2018-05-22) [Article]
      Carbon nanotubes (CNTs) have been widely used to improve the electrical conductivity of polymers. However, not all CNTs actively participate in the conduction of electricity since they have to be close to each other to form a conductive network. The amount of active CNTs is rarely discussed as it is not captured by percolation theory. However, this amount is a very important information that could be used in a definition of loading efficiency for CNTs (and, in general, for any nanofiller). Thus, we develop a computational tool to quantify the amount of CNTs that actively participates in the conductive network. We then use this quantity to propose a definition of loading efficiency. We compare our results with an expression presented in the literature for the fraction of percolated CNTs (although not presented as a definition of efficiency). We found that this expression underestimates the fraction of percolated CNTs. We thus propose an improved estimation. We also study how efficiency changes with CNT loading and the CNT aspect ratio. We use this concept to study the size of the representative volume element (RVE) for polymers loaded with CNTs, which has received little attention in the past. Here, we find the size of RVE based on both loading efficiency and electrical conductivity such that the scales of “morphological” and “functional” RVEs can be compared. Additionally, we study the relations between particle and network properties (such as efficiency, CNT conductivity and junction resistance) and the conductivity of CNT/polymer composites. We present a series of recommendations to improve the conductivity of a composite based on our simulation results.
    • Intra-pulse laser absorption sensor with cavity enhancement for oxidation experiments in a rapid compression machine

      Nasir, Ehson Fawad; Farooq, Aamir (Optics Express, The Optical Society, 2018-05-23) [Article]
      A sensor based on a mid-IR pulsed quantum cascade laser (QCL) and off-axis cavity enhanced absorption spectroscopy (OA-CEAS) has been developed for highly sensitive concentration measurements of carbon monoxide (CO) in a rapid compression machine. The duty cycle and the pulse repetition rate of the laser were optimized for increased tuning range, high chirp rate, and small line width to achieve effective laser-cavity coupling. This enabled spectrally resolved CO line-shape measurements at high pressures (P ~10 bar). A gain factor of 133 and a time resolution of 10 μs were demonstrated. CO concentration-time profiles during the oxidation of highly dilute n-octane/air mixtures were recorded, illustrating new opportunities in RCM experiments for chemical kinetics.
    • Carbon-based nanomaterial synthesis using nanosecond electrical discharges in immiscible layered liquids: <i>n</i>-heptane and water

      Hamdan, Ahmad; Cha, Min (Journal of Physics D: Applied Physics, IOP Publishing, 2018-05-14) [Article]
      Plasmas in- or in-contact with liquids have been extensively investigated due to their high potential for a wide range of applications including but not limited to, water treatment, material synthesis and functionalization, bio-medical applications, and liquid fuel reformation. Recently, we successfully developed a discharge using two immiscible liquids, having very different electrical permittivities, which could significantly intensify the electric field intensity. Here, we establish nanosecond discharges at the interface n-heptane-water (with respective relative dielectric permittivities of 2 and 80) to enable the synthesis of carbon-based nanomaterials. A characterization of the as-synthesized material and the annealed (500 °C) material, using various techniques (Fourier-Transform, Infra-Red, Scanning and Transmission electron microscopes, etc.), shows that the as-synthesized material is a mixture of two carbon-based phases: a crystalline phase (graphite like) embedded into a phase of hydrogenated amorphous carbon. The existence of two-phases may be explained by the non-homogeneity of the discharge that induces various chemical reactions in the plasma channel.
    • Autoignited lifted flames of dimethyl ether in heated coflow air

      Al-Noman, Saeed M.; Choi, Byung Chul; Chung, Suk-Ho (Combustion and Flame, Elsevier BV, 2018-05-16) [Article]
      Autoignited lifted flames of dimethyl ether (DME) in laminar nonpremixed jets with high-temperature coflow air have been studied experimentally. When the initial temperature was elevated to over 860 K, an autoignition occurred without requiring an external ignition source. A planar laser-induced fluorescence (PLIF) technique for formaldehyde (CH2O) visualized qualitatively the zone of low temperature kinetics in a premixed flame. Two flame configurations were investigated; (1) autoignited lifted flames with tribrachial edge having three distinct branches of a lean and a rich premixed flame wings with a trailing diffusion flame and (2) autoignited lifted flames with mild combustion when the fuel was highly diluted. For the autoignited tribrachial edge flames at critical autoignition conditions, exhibiting repetitive extinction and re-ignition phenomena near a blowout condition, the characteristic flow time (liftoff height scaled with jet velocity) was correlated with the square of the ignition delay time of the stoichiometric mixture. The liftoff heights were also correlated as a function of jet velocity times the square of ignition delay time. Formaldehydes were observed between the fuel nozzle and the lifted flame edge, emphasizing a low-temperature kinetics for autoignited lifted flames, while for a non-autoignited lifted flame, formaldehydes were observed near a thin luminous flame zone.For the autoignited lifted flames with mild combustion, especially at a high temperature, a unique non-monotonic liftoff height behavior was observed; decreasing and then increasing liftoff height with jet velocity. This behavior was similar to the binary mixture fuels of CH4/H2 and CO/H2 observed previously. A transient homogeneous autoignition analysis suggested that such decreasing behavior with jet velocity can be attributed to partial oxidation characteristics of DME in producing appreciable amounts of CH4/CO/H2 ahead of the edge flame region.
    • Intra-pulse Cavity Enhanced Measurements of Carbon Monoxide in a Rapid Compression Machine

      Nasir, Ehson Fawad; Farooq, Aamir (Conference on Lasers and Electro-Optics, OSA, 2018-05-07) [Conference Paper]
      A laser absorption sensor for carbon monoxide concentration was developed for combustion studies in a rapid compression machine using a pulsed quantum cascade laser near 4.89 μm. Cavity enhancement reduced minimum detection limit down to 2.4 ppm at combustion relevant conditions. Off-axis alignment and rapid intra-pulse down-chirp resulted in effective suppression of cavity noise.
    • Towards Real-Time Distributed Planning in Multi-Robot Systems

      Abdelkader, Mohamed (2018-04) [Dissertation]
      Advisor: Shamma, Jeff S.
      Committee members: Younis, Mohammad I.; Laleg-Kirati, Taous-Meriem; Chasparis, Georgios
      Recently, there has been an increasing interest in robotics related to multi-robot applications. Such systems can be involved in several tasks such as collaborative search and rescue, aerial transportation, surveillance, and monitoring, to name a few. There are two possible architectures for the autonomous control of multi-robot systems. In the centralized architecture, a master controller communicates with all the robots to collect information. It uses this information to make decisions for the entire system and then sends commands to each robot. In contrast, in the distributed architecture, each robot makes its own decision independent from a central authority. While distributed architecture is a more portable solution, it comes at the expense of extensive information exchange (communication). The extensive communication between robots can result in decision delays because of which distributed architecture is often impractical for systems with strict real-time constraints, e.g. when decisions have to be taken in the order of milliseconds. In this thesis, we propose a distributed framework that strikes a balance between limited communicated information and reasonable system-wide performance while running in real-time. We implement the proposed approach in a game setting of two competing teams of drones, defenders and attackers. Defending drones execute a proposed linear program algorithm (using only onboard computing modules) to obstruct attackers from infiltrating a defense zone while having minimal local message passing. Another main contribution is that we developed a realistic simulation environment as well as lab and outdoor hardware setups of customized drones for testing the system in realistic scenarios. Our software is completely open-source and fully integrated with the well-known Robot Operating System (ROS) in hopes to make our work easily reproducible and for rapid future improvements.
    • All Organic Polymers Based Morphing Skin with Controllable Surface Texture

      Favero Bolson, Natanael (2018-05) [Thesis]
      Advisor: Lubineau, Gilles
      Committee members: Salama, Khaled N.; Thoroddsen, Sigurdur T
      Smart skins are integrating an increasing number of functionalities in order to improve the interaction between the systems they equip and their ambient environment. Here we have developed an electromechanical soft actuator with controlled surface texture due to applied thermal gradient via electrical voltage. The device was fabricated and integrated with optimized process parameters for a prepared heater element [doped PEDOT: PSS (poly-(3, 4 ethylenedioxythiophene): poly (styrene sulfonic acid))], a soft actuator (Ecoflex 00-50/ethanol) and overall packaging case [PDMS (polydimethylsiloxane)]. To study a potential application of the proposed smart skin, we analyze the fluid drag reduction in a texture controlled water flow unit. As a result, we obtained a reduction of approximately 14% in the skin drag friction coefficient during the actuation. We conclude that the proposed soft actuator device is a preferred option for a texture-controlled skin that reduces the skin drag friction coefficient.
    • Low Load Limit Extension for Gasoline Compression Ignition Using Negative Valve Overlap Strategy

      Vallinayagam, R.; AlRamadan, Abdullah S.; Vedharaj, S; An, Yanzhao; Sim, Jaeheon; Chang, Junseok; Johansson, Bengt (SAE Technical Paper Series, SAE International, 2018-04-03) [Conference Paper]
      Gasoline compression ignition (GCI) is widely studied for the benefits of simultaneous reduction in nitrogen oxide (NO) and soot emissions without compromising the engine efficiency. Despite this advantage, the operational range for GCI is not widely expanded, as the auto-ignition of fuel at low load condition is difficult. The present study aims to extend the low load operational limit for GCI using negative valve overlap (NVO) strategy. The engine used for the current experimentation is a single cylinder diesel engine that runs at an idle speed of 800 rpm with a compression ratio of 17.3. The engine is operated at homogeneous charge compression ignition (HCCI) and partially premixed combustion (PPC) combustion modes with the corresponding start of injection (SOI) at 180 CAD (aTDC) and 30 CAD (aTDC), respectively. In the presented work, intake air temperature is used as control parameter to maintain combustion stability at idle and low load condition, while the intake air pressure is maintained at 1 bar (ambient). The engine is equipped with variable valve cam phasers that can phase both inlet and exhaust valves from the original timing. For the maximum cam phasing range (56 CAD) at a valve lift of 0.3 mm, the maximum allowable positive valve overlap was 20 CAD. In the present study, the exhaust cam is phased to 26 CAD and 6 CAD and the corresponding NVO is noted to be 10 CAD and 30 CAD, respectively. With exhaust cam phasing adjustment, the exhaust valve is closed early to retain hot residual gases inside the cylinder. As such, the in-cylinder temperature is increased and a reduction in the required intake air temperature to control combustion phasing is possible. For a constant combustion phasing of 3 CAD (aTDC), a minimum load of indicated mean effective pressure (IMEP) = 1 bar is attained for gasoline (RON = 91) at HCCI and PPC modes. The coefficient of variance was observed to below 5% at these idle and low load conditions. At the minimum load point, the intake air temperature required dropped by 20°C and 15°C for NVO = 30 CAD at HCCI and PPC modes, respectively, when compared to NVO = 20 CAD and NVO = 10 CAD. Similarly, for the load range of IMEP = 1 to 3 bar, decrease in temperature requirement is noted for negative valve overlap cases and the translational table in terms of d (Tin)/d (NVO) is attained. However, the low load limit was extended with negative valve overlap at the expense of decreased net indicated thermal efficiency due to heat losses and reduction in gas exchange efficiency. Ultra low soot concentration and NO emission were noted at HCCI condition.
    • Phase Transition Control for High-Performance Blade-Coated Perovskite Solar Cells

      Li, Jianbo; Munir, Rahim; Fan, Yuanyuan; Niu, Tianqi; Liu, Yucheng; Zhong, Yufei; Yang, Zhou; Tian, Yuansi; Liu, Bo; Sun, Jie; Smilgies, Detlef-M.; Thoroddsen, Sigurdur T; Amassian, Aram; Zhao, Kui; Liu, Shengzhong (Frank) (Joule, Elsevier BV, 2018-05-07) [Article]
      Summary Here, we have identified that the key issue for rational transitioning from spin-coating to blade-coating processes of perovskite films arises from whether intermediate phases participate in the phase transition. In situ characterizations were carried out to provide a comprehensive picture of structural evolution and crystal growth mechanisms. These findings present opportunities for designing an effective process for blade-coating perovskite film: a large-grained dense perovskite film with high crystal quality and photophysical properties can be obtained only via direct crystallization for both spin-coating and blade-coating processes. As a result, the blade-coated MAPbI3 films deliver excellent charge-collection efficiency at both short circuit and open circuit, and photovoltaic properties with efficiencies of 18.74% (0.09 cm2) and 17.06% (1 cm2) in planar solar cells. The significant advances in understanding how the phase transition links spin-coating and blade-coating processes should provide a path toward high-performance printed perovskite devices.
    • Standardized Gasoline Compression Ignition Fuels Matrix

      Badra, Jihad; Bakor, Radwan; AlRamadan, Abdullah; Almansour, Mohammed; Sim, Jaeheon; Ahmed, Ahfaz; Viollet, Yoann; Chang, Junseok (SAE Technical Paper Series, SAE International, 2018-04-03) [Conference Paper]
      Direct injection compression ignition engines running on gasoline-like fuels have been considered an attractive alternative to traditional spark ignition and diesel engines. The compression and lean combustion mode eliminates throttle losses yielding higher thermodynamic efficiencies and the better mixing of fuel/air due to the longer ignition delay times of the gasoline-like fuels allows better emission performance such as nitric oxides (NOx) and particulate matter (PM). These gasoline-like fuels which usually have lower octane compared to market gasoline have been identified as a viable option for the gasoline compression ignition (GCI) engine applications due to its lower reactivity and lighter evaporation compared to diesel. The properties, specifications and sources of these GCI fuels are not fully understood yet because this technology is relatively new. In this work, a GCI fuel matrix is being developed based on the significance of certain physical and chemical properties in GCI engine operation. Those properties were chosen to be density, temperature at 90 volume % evaporation (T90) or final boiling point (FBP) and research octane number (RON) and the ranges of these properties were determined from the data reported in literature. These proposed fuels were theoretically formulated, while applying realistic constraints, using species present in real refinery streams. Finally, three-dimensional (3D) engine computational fluid dynamics (CFD) simulations were performed using the proposed GCI fuels and the similarities and differences were highlighted.
    • Nonlinear viscoelasticity of pre-compressed layered polymeric composite under oscillatory compression

      Xu, Yangguang; Tao, Ran; Lubineau, Gilles (Composites Science and Technology, Elsevier BV, 2018-05-03) [Article]
      Describing nonlinear viscoelastic properties of polymeric composites when subjected to dynamic loading is essential for development of practical applications of such materials. An efficient and easy method to analyze nonlinear viscoelasticity remains elusive because the dynamic moduli (storage modulus and loss modulus) are not very convenient when the material falls into nonlinear viscoelastic range. In this study, we utilize two methods, Fourier transform and geometrical nonlinear analysis, to quantitatively characterize the nonlinear viscoelasticity of a pre-compressed layered polymeric composite under oscillatory compression. We discuss the influences of pre-compression, dynamic loading, and the inner structure of polymeric composite on the nonlinear viscoelasticity. Furthermore, we reveal the nonlinear viscoelastic mechanism by combining with other experimental results from quasi-static compressive tests and microstructural analysis. From a methodology standpoint, it is proved that both Fourier transform and geometrical nonlinear analysis are efficient tools for analyzing the nonlinear viscoelasticity of a layered polymeric composite. From a material standpoint, we consequently posit that the dynamic nonlinear viscoelasticity of polymeric composites with complicated inner structures can also be well characterized using these methods.
    • Appearance of deterministic mixing behavior from ensembles of fluctuating hydrodynamics simulations of the Richtmyer-Meshkov instability

      Narayanan, Kiran; Samtaney, Ravi (Physical Review E, American Physical Society (APS), 2018-04-19) [Article]
      We obtain numerical solutions of the two-fluid fluctuating compressible Navier-Stokes (FCNS) equations, which consistently account for thermal fluctuations from meso- to macroscales, in order to study the effect of such fluctuations on the mixing behavior in the Richtmyer-Meshkov instability (RMI). The numerical method used was successfully verified in two stages: for the deterministic fluxes by comparison against air-SF6 RMI experiment, and for the stochastic terms by comparison against the direct simulation Monte Carlo results for He-Ar RMI. We present results from fluctuating hydrodynamic RMI simulations for three He-Ar systems having length scales with decreasing order of magnitude that span from macroscopic to mesoscopic, with different levels of thermal fluctuations characterized by a nondimensional Boltzmann number (Bo). For a multidimensional FCNS system on a regular Cartesian grid, when using a discretization of a space-time stochastic flux Z(x,t) of the form Z(x,t)→1/-tN(ih,nΔt) for spatial interval h, time interval Δt, h, and Gaussian noise N should be greater than h0, with h0 corresponding to a cell volume that contains a sufficient number of molecules of the fluid such that the fluctuations are physically meaningful and produce the right equilibrium spectrum. For the mesoscale RMI systems simulated, it was desirable to use a cell size smaller than this limit in order to resolve the viscous shock. This was achieved by using a modified regularization of the noise term via Zx,t→1/-tmaxh3,h03Nih,nΔt, with h0=ξh<h0,ξZ+. Our simulations show that for systems with Bo1 deterministic mixing behavior emerges as the ensemble-averaged behavior of several fluctuating instances, whereas when Bo≈1, a deviation from deterministic behavior is observed. For all cases, the FCNS solution provides bounds on the growth rate of the amplitude of the mixing layer.
    • A Single MEMS Resonator for Reconfigurable Multifunctional Logic Gates

      Tella, Sherif Adekunle; Alcheikh, Nouha; Younis, Mohammad I. (Journal of Micromechanics and Microengineering, IOP Publishing, 2018-04-30) [Article]
      Despite recent efforts toward true electromechanical resonator-based computing, achieving complex logics functions through cascading micro resonators has been deterred by challenges involved in their interconnections and the large required array of resonators. In this work we present a single micro electromechanical resonator with two outputs that enables the realization of multifunctional logic gates as well as other complex logic operations. As examples, we demonstrate the realization of the fundamental 2-bit logic gates of OR, XOR, AND, NOR, and a half adder. The device is based on a compound resonator consisting of a clamped-guided electrostatically actuated arch beam that is attached to another resonant beam from the side, which serves as an additional actuation electrode for the arch. The structure is also provided with an additional electrothermal tuning capability. The logic operations are based on the linear frequency modulations of the arch resonator and side microbeam. The device is compatible with CMOS fabrication process and works at room temperature
    • Auto-Ignition and Spray Characteristics of n-Heptane and iso-Octane Fuels in Ignition Quality Tester

      Jaasim, Mohammed; Elhagrasy, Ayman; Sarathy, Mani; Chung, Suk-Ho; Im, Hong G. (SAE Technical Paper Series, SAE International, 2018-04-04) [Conference Paper]
      Numerical simulations were conducted to systematically assess the effects of different spray models on the ignition delay predictions and compared with experimental measurements obtained at the KAUST ignition quality tester (IQT) facility. The influence of physical properties and chemical kinetics over the ignition delay time is also investigated. The IQT experiments provided the pressure traces as the main observables, which are not sufficient to obtain a detailed understanding of physical (breakup, evaporation) and chemical (reactivity) processes associated with auto-ignition. A three-dimensional computational fluid dynamics (CFD) code, CONVERGE™, was used to capture the detailed fluid/spray dynamics and chemical characteristics within the IQT configuration. The Reynolds-averaged Navier-Stokes (RANS) turbulence with multi-zone chemistry sub-models was adopted with a reduced chemical kinetic mechanism for n-heptane and iso-octane. The emphasis was on the assessment of two common spray breakup models, namely the Kelvin-Helmholtz/Rayleigh-Taylor (KH-RT) and linearized instability sheet atomization (LISA) models, in terms of their influence on auto-ignition predictions. Two spray models resulted in different local mixing, and their influence in the prediction of auto-ignition was investigated. The relative importance of physical ignition delay, characterized by spray evaporation and mixing processes, in the overall ignition behavior for the two different fuels were examined. The results provided an improved understanding of the essential contribution of physical and chemical processes that are critical in describing the IQT auto-ignition event at different pressure and temperature conditions, and allowed a systematic way to distinguish between the physical and chemical ignition delay times.
    • Numerical convergence of discrete exterior calculus on arbitrary surface meshes

      Mohamed, Mamdouh S.; Hirani, Anil N.; Samtaney, Ravi (International Journal for Computational Methods in Engineering Science and Mechanics, Informa UK Limited, 2018-02-13) [Article]
      Discrete exterior calculus (DEC) is a structure-preserving numerical framework for partial differential equations solution, particularly suitable for simplicial meshes. A longstanding and widespread assumption has been that DEC requires special (Delaunay) triangulations, which complicated the mesh generation process especially for curved surfaces. This paper presents numerical evidence demonstrating that this restriction is unnecessary. Convergence experiments are carried out for various physical problems using both Delaunay and non-Delaunay triangulations. Signed diagonal definition for the key DEC operator (Hodge star) is adopted. The errors converge as expected for all considered meshes and experiments. This relieves the DEC paradigm from unnecessary triangulation limitation.
    • Effect of pressure on the transfer functions of premixed methane and propane swirl flames

      Di Sabatino, Francesco; Guiberti, Thibault F.; Boyette, Wesley; Roberts, William L.; Moeck, Jonas P.; Lacoste, Deanna (Combustion and Flame, Elsevier BV, 2018-04-24) [Article]
      This paper reports on the effect of pressure on the response of methane–air and propane–air swirl flames to acoustic excitation of the flow. These effects are analyzed on the basis of the flame transfer function (FTF) formalism, experimentally determined from velocity and global OH* chemiluminescence measurements at pressures up to 5 bar. In parallel, phase-locked images of OH* chemiluminescence are collected and analyzed in order to determine the associated flame dynamics. Flame transfer functions and visual flame dynamics at atmospheric pressure are found to be similar to previous studies with comparable experimental conditions. Regardless of pressure, propane flames exhibit a much larger FTF gain than methane flames. For both fuels, the effect of pressure primarily is to modify the gain response at the local maximum of the FTF, at a Strouhal number around 0.5 (176 Hz). For methane flames, this gain maximum increases monotonically with pressure, while for propane flames it increases from 1 to 3 bar and decreases from 3 to 5 bar. At this frequency and regardless of pressure, the flame motion is driven by flame vortex roll-up, suggesting that pressure affects the FTF by modifying the interaction of the flame with the vortex detached from the injector rim during a forcing period. The complex heat transfer, fluid dynamics, and combustion coupling in this configuration does not allow keeping the vortex properties constant when pressure is increased. However, the different trends of the FTF gain observed for methane and propane fuels with increasing pressure imply that intrinsic flame properties and fuel chemistry, and their variation with pressure, play an important role in controlling the response of these flames to acoustic forcing.
    • Computational singular perturbation analysis of super-knock in SI engines

      Jaasim, Mohammed; Tingas, Alexandros; Hernández Pérez, Francisco E.; Im, Hong G. (Fuel, Elsevier BV, 2018-04-02) [Article]
      Pre-ignition engine cycles leading to super-knock were simulated with a 48 species skeletal iso-octane mechanism to identify the dominant reaction pathways that are present in super-knock. To mimic pre-ignition, a deflagration front was generated via a hot spot that is placed over the piston at close proximity to the end-wall. Computational singular perturbation (CSP) was used to analyze the chemical dynamics at various in-cylinder locations: a point at the center of the cylinder where the deflagration front consumes the air/fuel mixture and two points located at 3 mm from the end-wall where super-knock and mild knock occur. The CSP analysis of the point at the center of the cylinder reveals weak two-stage ignition-like dynamics with a short second stage. At the other points, a pronounced two-stage ignition is displayed with a long second stage. A distinct contribution of formaldehyde (CHO) at the second stage of ignition that adds to fast explosive modes in the super-knock points is not observed in the point at the center. A comparison between knock and super-knock analysis indicates that a similar set of reactions is responsible for the abnormal behavior but the fast explosive time scales are comparatively slower for knock, indicating lower reactivity, which results in the reduced intensity of knock. The analyzed results decoded important reactions responsible for the occurrence of super-knock.
    • An investigation of the mechanical behavior of initially curved microplates under electrostatic actuation

      Saghir, Shahid; Younis, Mohammad I. (Acta Mechanica, Springer Nature, 2018-03-28) [Article]
      In this article, we investigate the mechanical behavior of initially curved microplates under electrostatic actuation. Microplates are essential components of many Micro-Electro-Mechanical System devices; however, they commonly undergo an initial curvature imperfection, due to the microfabrication process. Initial curvature imperfection significantly affects the mechanical behavior of microplates. In this work, we derive a dynamic analogue of the von Kármán governing equation for such plates. These equations are then used to develop a reduced order model based on the Galerkin procedure to simulate the static and dynamic behavior of the microplate. Two profiles of initial curvature commonly encountered in microfabricated structures are considered, where one assumes a variation in shape along one dimension of the plate only (cylindrical bending shape) while the other assumes a variation in shape along both dimensions of the plate. Their effects on both the static and dynamic responses of the microplates are examined and compared. We validate the reduced order model by comparing the calculated static behavior and the fundamental natural frequency with those computed by a finite element model over a range of the initial plate rise. The static behavior of the microplate is investigated when varying the DC voltage. Then, the dynamic behavior of the microplate is examined under the application of a harmonic AC voltage superimposed to a DC voltage.
    • Autoignition of isooctane beyond RON and MON conditions

      Masurier, Jean-Baptiste; Waqas, Muhammad; Sarathy, Mani; Johansson, Bengt (SAE Technical Paper Series, SAE International, 2018-04-03) [Conference Paper]
      The present study experimentally examines the low temperature autoignition area of isooctane within the in-cylinder pressure - in-cylinder temperature map. Experiments were run with the help of a CFR engine. The boundaries of this engine were extended so that experiments could be performed outside the domain delimited by RON and MON traces. Since HCCI combustion is governed by kinetics, the rotation speed for all the experiments was set at 600 rpm to allow time for low temperature heat release (LTHR). All the other parameters (intake pressure, intake temperature, compression ratio and equivalence ratio), were scanned, such as the occurrence of isooctane combustion. The principal results showed that LTHR for isooctane occurs effortlessly under high intake pressure (1.3 bar) and low intake temperature (25 °C). Increasing the intake temperature leads to the loss of the LTHR, and therefore to a smaller domain on the pressure-temperature trace. In such a case, the LTHR domain is restricted from 20 to 50 bar in pressure and from 600 to 850 K in temperature. By slightly decreasing the intake pressure, the LTHR domain remains unchanged, but the LTHR tends to disappear, and finally, at 1.0 bar, the LTHR domain ceases to exist. When the equivalence ratio is moved from 0.3 to 0.4, the LTHR domain is delimited in the same range of pressure and temperature, but the start of combustion occurs slightly earlier for the same pressure-temperature trace. Similar conclusions were drawn regarding the variation of both intake pressure and temperature, except that few LTHR points were observed under 1.0 bar intake.