We show that graphene-percolated polymer composites exhibit fractional capacitance response in the frequency range of 50 kHz–2 MHz. In addition, it is shown that by varying the loading of graphene within the matrix from 2.5% to 12%, the phase can be controllably tuned from −67° to −31°, respectively. The electrostatic fractional capacitors proposed herein are easy to fabricate and offer integration capability on electronic printed circuit boards.
Priante, Davide; Dursun, Ibrahim; Alias, M. S.; Shi, Dong; Melnikov, V. A.; Ng, Tien Khee; Mohammed, Omar F.; Bakr, Osman; Ooi, Boon S.(Applied Physics Letters, AIP Publishing, 2015-02-23)[Article]
We investigated the mechanisms of radiative recombination in a CH3NH3PbBr3 hybrid perovskite material using low-temperature, power-dependent (77K), and temperature-dependent photoluminescence (PL) measurements. Two bound-excitonic radiative transitions related to grain size inhomogeneity were identified. Both transitions led to PL spectra broadening as a result of concurrent blue and red shifts of these excitonic peaks. The red-shifted bound-excitonic peak dominated at high PL excitation led to a true-green wavelength of 553nm for CH3NH3PbBr3 powders that are encapsulated in polydimethylsiloxane. Amplified spontaneous emission was eventually achieved for an excitation threshold energy of approximately 350μJ/cm2. Our results provide a platform for potential extension towards a true-green light-emitting device for solid-state lighting and display applications.
Khan, M. A.; Bhansali, Unnat Sampatraj; Zhang, Xixiang; Saleh, Moussa M.; Odeh, Ihab; Alshareef, Husam N.(Applied Physics Letters, AIP Publishing, 2012-10-03)[Article]
Flexible ferroelectric capacitors with doped polymer electrodes have been fabricated on plastic substrates with performance as good as metal electrodes. The effect of doping on the morphology of polymer electrodes and its impact on device performance have been studied. Improved fatigue characteristics using doped and undoped poly (3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) electrodes versus metal electrodes are observed. It is shown that the polymer electrodes follow classical ferroelectric and dielectric responses, including series resistance effects. The improved device characteristics obtained using highly conducting doped PEDOT:PSS suggest that it may be used both as an electrode and as global interconnect for all-polymer transparent circuits on flexible substrates.
In the recent past, with the advent of transient electronics for mostly implantable and secured electronic applications, the whole field effect transistor structure has been dissolved in a variety of chemicals. Here, we show simple water soluble nano-scale (sub-10 nm) germanium oxide (GeO) as the dissolvable component to remove the functional structures of metal oxide semiconductor devices and then reuse the expensive germanium substrate again for functional device fabrication. This way, in addition to transiency, we also show an environmentally friendly manufacturing process for a complementary metal oxide semiconductor (CMOS) technology. Every year, trillions of complementary metal oxide semiconductor (CMOS) electronics are manufactured and billions are disposed, which extend the harmful impact to our environment. Therefore, this is a key study to show a pragmatic approach for water soluble high performance electronics for environmentally friendly manufacturing and bioresorbable electronic applications.
The spontaneous polarization (SP) and piezoelectric (PZ) constants of BxAl1-xN and BxGa1-xN (0 ≤ x ≤ 1) ternary alloys were calculated with the hexagonal structure as reference. The SP constants show moderate nonlinearity due to the volume deformation and the dipole moment difference between the hexagonal and wurtzite structures. The PZ constants exhibit significant bowing because of the large lattice difference between binary alloys. Furthermore, the PZ constants of BxAl1-xN and BxGa1-xN become zero at boron compositions of ∼87% and ∼74%, respectively, indicating non-piezoelectricity. The large range of SP and PZ constants of BxAl1-xN (BAlN) and BxGa1-xN (BGaN) can be beneficial for the compound semiconductor device development. For instance, zero heterointerface polarization ΔP can be formed for BAlN and BGaN based heterojunctions with proper B compositions, potentially eliminating the quantum-confined Stark effect for c-plane optical devices and thus removing the need of non-polar layers and substrates. Besides, large heterointerface polarization ΔP is available that is desirable for electronic devices.
Both β-Ga2O3 and wurtzite AlN have wide bandgaps of 4.5–4.9 and 6.1 eV, respectively. We calculated the in-plane lattice mismatch between the (−201) plane of β-Ga2O3 and the (0002) plane of AlN, which was found to be 2.4%. This is the smallest mismatch between β-Ga2O3 and binary III-nitrides which is beneficial for the formation of a high quality β-Ga2O3/AlN heterojunction. However, the valence and conduction band offsets (VBO and CBO) at the β-Ga2O3/AlN heterojunction have not yet been identified. In this study, a very thin (less than 2 nm) β-Ga2O3 layer was deposited on an AlN/sapphire template to form the heterojunction by pulsed laser deposition. High-resolution X-ray photoelectron spectroscopy revealed the core-level (CL) binding energies of Ga 3d and Al 2p with respect to the valence band maximum in individual β-Ga2O3 and AlN layers, respectively. The separation between Ga 3d and Al 2p CLs at the β-Ga2O3/AlN interface was also measured. Eventually, the VBO was found to be −0.55 ± 0.05 eV. Consequently, a staggered-gap (type II) heterojunction with a CBO of −1.75 ± 0.05 eV was determined. The identification of the band alignment of the β-Ga2O3/AlN heterojunction could facilitate the design of optical and electronic devices based on these and related alloys.
Sun, Haiding; Park, Young Jae; Li, Kuang-Hui; Torres Castanedo, C. G.; Alowayed, Abdulmohsen; Detchprohm, Theeradetch; Dupuis, Russell D.; Li, Xiaohang(Applied Physics Letters, AIP Publishing, 2017-09-21)[Article]
Owing to large bandgaps of BAlN and AlGaN alloys, their heterojunctions have the potential to be used in deep ultraviolet and power electronic device applications. However, the band alignment of such junctions has not been identified. In this work, we investigated the band-offset parameters of a BAlN/AlGaN heterojunction grown by metalorganic vapor phase epitaxy. These specific compositions were chosen to ensure a sufficiently large band offset for deep ultraviolet and power electronic applications. High resolution transmission electron microscopy confirmed the high structural quality of the heterojunction with an abrupt interface and uniform element distribution. We employed high resolution X-ray photoemission spectroscopy to measure the core level binding energies of B 1s and Ga 2p with respect to the valence band maximum of BAlN and AlGaN layers, respectively. Then, we measured the energy separation between the B 1s and Ga 2p core levels at the interface of the heterojunction. The valence band offset was determined to be 0.40 ± 0.05 eV. As a consequence, we identified a staggered-gap (type-II) heterojunction with the conduction band offset of 1.10 ± 0.05 eV. The determination of the band alignment of the BAlN/AlGaN heterojunction facilitates the design of optical and electronic devices based on such junctions.
Cavazos Sepulveda, Adrian Cesar; Diaz Cordero, M. S.; Carreno, Armando Arpys Arevalo; Nassar, Joanna M.; Hussain, Muhammad Mustafa(Applied Physics Letters, AIP Publishing, 2017-03-30)[Article]
Flexible and stretchable semiconducting substrates provide the foundation for novel electronic applications. Usually, ultra-thin, flexible but often fragile substrates are used in such applications. Here, we describe flexible, stretchable, and foldable 500-μm-thick bulk mono-crystalline silicon (100) “islands” that are interconnected via extremely compliant 30-μm-thick connectors made of silicon. The thick mono-crystalline segments create a stand-alone silicon array that is capable of bending to a radius of 130 μm. The bending radius of the array does not depend on the overall substrate thickness because the ultra-flexible silicon connectors are patterned. We use fracture propagation to release the islands. Because they allow for three-dimensional monolithic stacking of integrated circuits or other electronics without any through-silicon vias, our mono-crystalline islands can be used as a “more-than-Moore” strategy and to develop wearable electronics that are sufficiently robust to be compatible with flip-chip bonding.
Export search results
The export option will allow you to export the current search results of the entered query to a file. Different
formats are available for download. To export the items, click on the button corresponding with the preferred download format.
By default, clicking on the export buttons will result in a download of the allowed maximum amount of items.
For anonymous users the allowed maximum amount is 50 search results.
To select a subset of the search results, click "Selective Export" button and make a selection of the items you want to export.
The amount of items that can be exported at once is similarly restricted as the full export.
After making a selection, click one of the export format buttons. The amount of items that will be exported is indicated in the bubble next to export format.