Zhao, Chao; Ng, Tien Khee; Tseng, Chien-Chih; Li, Jun; Shi, Yumeng; Wei, Nini; Zhang, Daliang; Consiglio, Giuseppe Bernardo; Prabaswara, Aditya; Alhamoud, Abdullah; Albadri, Abdulrahman M.; Alyamani, Ahmed Y.; Zhang, Xixiang; Li, Lain-Jong; Ooi, Boon S.(RSC Adv., Royal Society of Chemistry (RSC), 2017)[Article]
The recent study of a wide range of layered transition metal dichalcogenides (TMDCs) has created a new era for device design and applications. In particular, the concept of van der Waals epitaxy (vdWE) utilizing layered TMDCs has the potential to broaden the family of epitaxial growth techniques beyond the conventional methods. We report herein, for the first time, the monolithic high-power, droop-free, and wavelength tunable InGaN/GaN nanowire light-emitting diodes (NW-LEDs) on large-area MoS2 layers formed by sulfurizing entire Mo substrates. MoS2 serves as both a buffer layer for high-quality GaN nanowires growth and a sacrificial layer for epitaxy lift-off. The LEDs obtained on nitridated MoS2 via quasi vdWE show a low turn-on voltage of ∼2 V and light output power up to 1.5 mW emitting beyond the “green gap”, without an efficiency droop up to the current injection of 1 A (400 A cm−2), by virtue of high thermal and electrical conductivities of the metal substrates. The discovery of the nitride/layered TMDCs/metal heterostructure platform also ushers in the unparalleled opportunities of simultaneous high-quality nitrides growth for high-performance devices, ultralow-profile optoelectronics, energy harvesting, as well as substrate reusability for practical applications.
Janjua, Bilal; Sun, Haiding; Zhao, Chao; Anjum, Dalaver H.; Wu, Feng; Alhamoud, Abdullah; Li, Xiaohang; Albadri, Abdulrahman M; Alyamani, Ahmed Y; El-Desouki , Munir M; Ng, Tien Khee; Ooi, Boon S.(Nanoscale, Royal Society of Chemistry (RSC), 2017)[Article]
The growth of self-assembled, vertically oriented and uniform nanowires (NWs) has remained a challenge for efficient light-emitting devices. Here, we demonstrate dislocation-free AlGaN NWs with spontaneous coalescence, which are grown by plasma-assisted molecular beam epitaxy on an n-type doped silicon (100) substrate. A high density of NWs (filling factor > 95%) was achieved under optimized growth conditions, enabling device fabrication without planarization using ultraviolet (UV)-absorbing polymer materials. UV-B (280-320 nm) light-emitting diodes (LEDs), which emit at ~303 nm with a narrow full width at half maximum (FWHM) (~20 nm) of the emission spectrum, are demonstrated using a large active region (“active region/NW length-ratio” ~ 50%) embedded with 15 stacks of AlxGa1-xN/AlyGa1-yN quantum-disks (Qdisks). To improve the carrier injection, a graded layer is introduced at the AlGaN/GaN interfaces on both p- and n-type regions. This work demonstrates a viable approach to easily fabricate ultra-thin, efficient UV optoelectronic devices on low-cost and scalable silicon substrates.
Zhao, Chao; Ebaid, Mohamed; Zhang, Huafan; Priante, Davide; Janjua, Bilal; Zhang, Daliang; Wei, Nini; Alhamoud, Abdullah; Shakfa, M. Khaled; Ng, Tien Khee; Ooi, Boon S.(Nanoscale, Royal Society of Chemistry (RSC), 2018)[Article]
P-type doping in wide bandgap and new classes of ultra-wide bandgap materials has long been a scientific and engineering problem. The challenges arise from the large activation energy of dopants and high densities of dislocations in materials. We report here, a significantly enhanced p-type conduction using high-quality AlGaN nanowires. For the first time, the hole concentration in Mg-doped AlGaN nanowires is quantified. The incorporation of Mg into AlGaN was verified by correlation with photoluminescence and Raman measurements. The open-circuit potential measurements further confirmed the p-type conductivity; while Mott-Schottky experiments measured a hole concentration of 1.3×1019 cm-3. These results from photoelectrochemical measurements allow us to design prototype ultraviolet (UV) light-emitting diodes (LEDs) incorporating the AlGaN quantum-disks-in-nanowire and optimized p-type AlGaN contact layer for UV-transparency. The ~335-nm LEDs exhibited a low turn-on voltage of 5 V with a series resistance of 32 Ω, due to the efficient p-type doping of the AlGaN nanowires. The bias-dependent Raman measurements further revealed the negligible self-heating of devices. This study provides an attractive solution to evaluate electrical properties of AlGaN, which is applicable to other wide bandgap nanostructures. Our results are expected to open doors to new applications for wide and ultra-wide bandgap materials.
Ebaid, Mohamed; Min, Jungwook; Zhao, Chao; Ng, Tien Khee; Idriss, Hicham; Ooi, Boon S.(Journal of Materials Chemistry A, Royal Society of Chemistry (RSC), 2018)[Article]
Water splitting using InGaN-based photocatalysts may have a great contribution in future renewable energy production systems. Among the most important parameters to solve are those related to substrate lattice-matching compatibility. Here, we directly grow InGaN nanowires (NWs) on a metallic Ti/Si template, for improving water splitting performance compared to a bare Si substrate. The open circuit potential of the epitaxially grown InGaN NWs on metallic Ti was almost two times that of those grown on Si substrate. The interfacial transfer resistance was also reduced significantly after introducing the metallic Ti interlayer. An applied-bias-photon-to-current conversion efficiency of 2.2% and almost unity Faradic efficiency for hydrogen generation were achieved using this approach. The InGaN NWs grown on Ti showed improved stability of hydrogen generation under continuous operation conditions, when compared to those grown on Si, emphasizing the role of the semiconductor-on-metal approach in enhancing the overall efficiency of water splitting catalysts.
Export search results
The export option will allow you to export the current search results of the entered query to a file. Different
formats are available for download. To export the items, click on the button corresponding with the preferred download format.
By default, clicking on the export buttons will result in a download of the allowed maximum amount of items.
For anonymous users the allowed maximum amount is 50 search results.
To select a subset of the search results, click "Selective Export" button and make a selection of the items you want to export.
The amount of items that can be exported at once is similarly restricted as the full export.
After making a selection, click one of the export format buttons. The amount of items that will be exported is indicated in the bubble next to export format.