Amin, Osama; Abediseid, Walid; Alouini, Mohamed-Slim(2017 IEEE Wireless Communications and Networking Conference (WCNC), Institute of Electrical and Electronics Engineers (IEEE), 2017-05-12)[Conference Paper]
Improper Gaussian signaling (IGS) has been recently shown to provide performance improvements in underlay cognitive radio systems as opposed to the conventional proper Gaussian signaling (PGS) scheme. For the first time, this paper implements IGS scheme in overlay cognitive radio system, where the secondary transmitter broadcasts a mixture of two different signals. The first signal is selected from the PGS scheme to support the primary message transmission. On the other hand, the second signal is chosen to be from the IGS scheme in order to reduce the interference effect on the primary receiver. We then optimally design the overlay cognitive radio that employs IGS to maximize the secondary link achievable rate while satisfying the minimum rate requirement of the primary network. In particular, we derive closed form expressions for the circularity coefficient used in the IGS scheme and the power distribution parameters. Simulation results are provided to support our theoretical derivations.
Javed, Sidrah; Amin, Osama; Alouini, Mohamed-Slim(2017 IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP), Institute of Electrical and Electronics Engineers (IEEE), 2017-06-20)[Conference Paper]
In this paper, we study the benefits of employing improper Gaussian signaling (IGS) in full duplex relaying (FDR) suffering from in-phase and quadrature imbalance (IQI). Different from the traditional symmetric signaling scheme, proper Gaussian signaling (PGS), that is parametrized by its variance, IGS needs additional statistical-quantity called the pseudo-variance to be fully described. The cooperative system under consideration suffers from two types of interferences, the residual self-interference (RSI) and IQI. To evaluate the system performance gain using IGS, first we express the end-to-end achievable rate for different IQI. Then, we optimize the pseudo-variance to compensate the interferences impact and improve the end-to-end achievable rate. Interestingly, IGS-based scheme outperforms its counterpart PGS-based scheme, especially at higher interference-to-noise ratio. Our findings reveal that using single-user detection with asymmetric signaling can compensate both RSI and IQI and improve the system performance.
Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim(2017 IEEE International Conference on Communications Workshops (ICC Workshops), Institute of Electrical and Electronics Engineers (IEEE), 2017-07-03)[Conference Paper]
Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.
Export search results
The export option will allow you to export the current search results of the entered query to a file. Different
formats are available for download. To export the items, click on the button corresponding with the preferred download format.
By default, clicking on the export buttons will result in a download of the allowed maximum amount of items.
For anonymous users the allowed maximum amount is 50 search results.
To select a subset of the search results, click "Selective Export" button and make a selection of the items you want to export.
The amount of items that can be exported at once is similarly restricted as the full export.
After making a selection, click one of the export format buttons. The amount of items that will be exported is indicated in the bubble next to export format.