Experimental kinetics results of propane in Maxsorb III activated carbon is obtained at temperatures of 10°C and 30°C, and pressures up to 800kPa using a magnetic suspension balance. A multi-gradient linear driving force (LDF) approximation is used for adsorbate uptake as a function of time. The LDF mass-transfer-rate coefficients were thus determined. Using this approach, the experimentally derived LDF coefficients based on independently measured kinetic parameters for propane in the activated-carbon bed agree very well with experimental results. The computational efficiency is gained by adopting this extended LDF model. © (2013) Trans Tech Publications, Switzerland.

SiO2/Silicalite-1 core-shell material has been demonstrated as potential shape selective adsorbent in gas phase separation of p-xylene from a mixture of p/o-xylene isomers. The core-shell composite comprised of large silica core and thin polycrystalline silicalite-1 shell which was synthesized via a self-assembly of silicalite-1 nanocrystals on core silica surface followed by a secondary seeded growth method. The core materials, SiO2 used in this study has mesoporosity with an average pore diameter of 60Å and hence offers no shape selectivity for xylene isomers. However, the shell, silicalite-1 contains rigid pore structures and preferentially adsorbs p-xylene from their isomers mixtures. A series of adsorption fixed bed breakthrough adsorption/desorption experiment was performed to obtain the equilibrium isotherms and adsorption isotherm parameters of xylene isomers. The equilibrium isotherms of xylene isomers follow the Langmuir's model. A chromatographic adsorption model has been used to describe the fixed-bed breakthrough profiles of xylene isomers. The model has successfully predicted the responses of the binary mixtures of p/o-xylene isomers. The SiO2/silicalite-1 core-shell adsorbents have shown para-selectivity as high as 15. © Bangladesh Uni. of Engg. & Tech.

This paper discusses the performance analysis of an advanced adsorption desalination (AD) cycle with an internal heat recovery between the condenser and the evaporator. The AD cycle employs the adsorption-desorption principles to convert sea or brackish water into high-grade potable water with total dissolved solids (TDS) less than 10 ppm (mg/L) utilizing low-temperature heat source. The salient features of the AD cycle are the utilization of low temperature waste heat (typically 55 C to 85 C) with the employment of an environment-friendly silica gel/water pair and the low maintenance as it has no major moving parts other than the pumps and valves. For improved performance of the AD pilot plant, the internal heat recovery scheme between the condenser and evaporator has been implemented with a run-about water circuit between them. The efficacy of the scheme is analyzed in terms of key performance indicators such as the specific daily water production (SDWP) and the performance ratio (PR). Extensive experiments were performed for assorted heat source temperatures ranging from 70 C to 50 C. From the experiments, the SDWP of the AD cycle with the proposed heat recovery scheme is found to be 15 m3 of water per ton of silica gel that is almost twice that of the yield obtained by a conventional AD cycle for the same operation conditions. Another important finding of AD desalination plant is that the advanced AD cycle could still be operational with an inlet heat source temperature of 50 C and yet achieving a SDWP of 4.3 m3 - a feat that never seen by any heat-driven cycles. © 2013 Elsevier Ltd. All rights reserved.

Desalination, other than the natural water cycle, is hailed as the panacea to alleviate the problems of fresh water shortage in many water stressed countries. However, the main drawback of conventional desalination methods is that they are energy intensive. In many instances, they consumed electricity, chemicals for pre- and post-treatment of water. For each kWh of energy consumed, there is an unavoidable emission of Carbon Dioxide (CO2) at the power stations as well as the discharge of chemically-laden brine into the environment. Thus, there is a motivation to find new direction or methods of desalination that consumed less chemicals, thermal energy and electricity.This paper describes an emerging and yet low cost method of desalination that employs only low-temperature waste heat, which is available in abundance from either the renewable energy sources or exhaust of industrial processes. With only one heat input, the Adsorption Desalination (AD) cycle produces two useful effects, i.e., high grade potable water and cooling. In this article, a brief literature review, the theoretical framework for adsorption thermodynamics, a lumped-parameter model and the experimental tests for a wide range of operational conditions on the basic and the hybrid AD cycles are discussed. Predictions from the model are validated with measured performances from two pilot plants, i.e., a basic AD and the advanced AD cycles. The energetic efficiency of AD cycles has been compared against the conventional desalination methods. Owing to the unique features of AD cycle, i.e., the simultaneous production of dual useful effects, it is proposed that the life cycle cost (LCC) of AD is evaluated against the LCC of combined machines that are needed to deliver the same quantities of useful effects using a unified unit of $/MWh. In closing, an ideal desalination system with zero emission of CO2 is presented where geo-thermal heat is employed for powering a temperature-cascaded cogeneration plant. © 2012 Elsevier B.V.

Low temperature waste heat-driven adsorption desalination (AD) cycles offer high potential as one of the most economically viable and environmental-friendly desalination methods. This article presents the development of an advanced adsorption desalination cycle that employs internal heat recovery between the evaporator and the condenser, utilizing an encapsulated evaporator-condenser unit for effective heat transfer. A simulation model has been developed based on the actual sorption characteristics of the adsorbent-adsorbate pair, energy and mass balances applied to the components of the AD cycle. With an integrated design, the temperature in the evaporator and the vapor pressurization of the adsorber are raised due to the direct heat recovery from the condenser, resulting in the higher water production rates, typically improved by as much as three folds of the conventional AD cycle. In addition, the integrated design eliminates two pumps, namely, the condenser cooling water and the chilled water pumps, lowering the overall electricity consumption. The performance of the cycle is analyzed at assorted heat source and cooling water temperatures, and different cycle times as well as the transient heat transfer coefficients of the evaporation and condensation. © 2012 Elsevier B.V.

This paper presents the performance testing of Zeolite adsorption cooling system driven by low grade waste heat source extracted from prime mover's exhaust, power plant's exhaust and the solar energy. The adsorbent FAM Z01 is used as an adsorbent in the adsorption chiller facility. Owing to its large equilibrium pore volume, it has the high affinity for the water vapor adsorbate. The key advantages of the Zeolite adsorption cooling system are: (i) it has no moving parts rendering less maintenance, (ii) the energy efficient means of cooling by the adsorption process with a low temperature heat source, (iii) the use of vapor pipes are replaced by self actuating vapor valves rendering smaller footprint area and (iv) it is environmental friendly with low carbon footprint. The experimental investigations were carried out for Zeolite adsorption chiller at different key operating conditions namely (i) heat source temperature, (ii) the cycle time and (iii) the heat recovery time. It is investigated that performance of coefficient (COP) of this system could be as high as 0.48 while the waste heat source temperature is applicable as low as 55 °C. © 2012.

Energy or heat recovery schemes are keys for the performance improvement of any heat-activated cycles such as the absorption and adsorption cycles. We present two innovative heat recovery schemes between the condensing and evaporating units of an adsorption desalination (AD) cycle. By recovering the latent heat of condenser and dumping it into the evaporative process of the evaporator, it elevates the evaporating temperature and hence the adsorption pressure seen by the adsorbent. From isotherms, this has an effect of increasing the vapour uptake. In the proposed configurations, one approach is simply to have a run-about water circuit between the condenser and the evaporator and a pump is used to achieve the water circulation. This run-around circuit is a practical method for retrofitting purposes. The second method is targeted towards a new AD cycle where an encapsulated condenser-evaporator unit is employed. The heat transfer between the condensing and evaporative vapour is almost immediate and the processes occur in a fully integrated vessel, thereby minimizing the heat transfer resistances of heat exchangers. © 2013 Desalination Publications.

This paper describes the development of a simple hybrid desalination system of a Multi-Effect Distillation (MED) and an adsorption (AD) cycle operating at sub-atmospheric pressures and temperatures. By hybridizing the conventional MED with an AD cycle, there is a symbiotic enhancement of performances of both cycles. The performance enhancement is attributed to (i) the cascade of adsorbent's regeneration temperature and this extended the usage of thermal energy emanating from the brine heater and (ii) the vapor extraction from the last MED stage by AD cycle which provides the effect of lowering saturation temperatures of all MED stages to the extent of 5°C, resulting in scavenging of heat leaks into the MED stages from the ambient. The combined effects of the hybrid cycles increase the water production capacity of the desalination plant by nearly twofolds.In this paper, we demonstrate a hybrid cycle by simulating an 8-stage MED cycle which is coupled to an adsorption cycle for direct vapor extraction from the last MED stage. The sorption properties of silica gel is utilized (acting as a mechanical vapor compressor) to reduce the saturation temperatures of MED stages. The modeling utilizes the adsorption isotherms and kinetics of the adsorbent. +. adsorbate (silica-gel. +. water) pair along with the governing equations of mass, energy and concentration. For a 8-stage MED and AD cycles operating at assorted temperatures of 65-90°C, the results show that the water production rate increases from 60% to twofolds when compared to the MED alone. The performance ratio (PR) and gain output ratio (GOR) also improve significantly. © 2012 Elsevier Ltd.

This paper discusses the analysis of an adsorption (AD) chiller using system entropy generation as a thermodynamic framework for evaluating total dissipative losses that occurred in a batch-operated AD cycle. The study focuses on an adsorption cycle operating at heat source temperatures ranging from 60 to 85 °C, whilst the chilled water inlet temperature is fixed at 12.5 °C,-a temperature of chilled water deemed useful for dehumidification and cooling. The total entropy generation model examines the processes of key components of the AD chiller such as the heat and mass transfer, flushing and de-superheating of liquid refrigerant. The following key findings are observed: (i) The cycle entropy generation increases with the increase in the heat source temperature (10.8 to 46.2 W/K) and the largest share of entropy generation or rate of energy dissipation occurs at the adsorption process, (ii) the second highest energy rate dissipation is the desorption process, (iii) the remaining energy dissipation rates are the evaporation and condensation processes, respectively. Some of the noteworthy highlights from the study are the inevitable but significant dissipative losses found in switching processes of adsorption-desorption and vice versa, as well as the de-superheating of warm condensate that is refluxed at non-thermal equilibrium conditions from the condenser to the evaporator for the completion of the refrigeration cycle. © 2012 Elsevier Ltd. All rights reserved.

Thermo-physical properties, surface characteristics and water vapor uptake capacity are key parameters in the selection of adsorbent for an adsorption desalination (AD) cycle. In the AD cycles, silica gel is used as adsorbent due to their high water vapor uptake capacity, reliability, repeatability and inexpensiveness as compared to other adsorbents. Three types of commercially available silica gels (Type-RD 2560,Type-A5BW and Type-A++) are investigated using a surface characteristic analyzer and their thermo-physical properties are evaluated using several analysis methods. The instrument used in this investigation employs the static volumetric method with liquid Nitrogen at 77 K as the filing fluid. The surface area of each adsorbent is studied using Brunauer-Emmett-Teller (BET) method whilst the pore size distribution (PSD) analysis is conducted with the Non-Local Density Functional Theory (NLDFT). It is observed that the Type-A++ silica gel (granular type) possesses the highest surface area of 863.6 m2/g amongst the three parent silica gels studied. It has a two-maxima or bimodal distribution pattern where the pore diameters are distributed mostly between 10 Å and 30 Å. Water vapor uptake capacity of silica gels are studied with water vapor dosage apparatus and the results show that the Type-A++ silica gel exhibits a highest equilibrium uptake at 537 cm3/g. These thermo-physical properties are essential for the design and the numerical simulation of AD cycles. © 2012 Published by Elsevier Ltd.